Tag Archives: 3-axis

Youtube user, Yakir Yahish,  posted this quick video of him doing a driving test with the CAME-Single gimbal!

Click below for more information on the CAME-Single 3-Axis Gimbal.

CAME-Single 3-Axis Gimbal

Vimeo user, No Routes Found, posted this quick review of the CAME-7800 Gimbal while he was on location shooting a documentary. Check it out below!

Click below for more information on the CAME-TV 7800 3-Axis Gimbal.

CAME-TV 7800 3-Axis Gimbal

Recently, Vimeo user, Kluzo, used the CAME-7800 gimbal to cover an event in Paris!
The CAME-7800 uses three motors that stabilize the camera along with the pan, tilt, and roll axis. The motors will help compensate for shakes, vibrations, and other unwanted movements, allowing you to get some smooth shots.

CAME-TV 7800 3-Axis Gimbal
(Monitor Is Optional)

Click below for more information on the CAME-7800 3-Axis Gimbal.

CAME-TV 7800 3-Axis Gimbal

 

In this quick video posted by Youtube user, Joe Taravella, he takes his new CAME-Single gimbal out for a test run! The footage looks great, especially when he walks up and down the stairs. He used his Sony A7S with a Sony 10-18mm F4 lens.The new CAME-Single is one of the first commercially available 3-Axis 32-bit basecam controlled gimbals that offer brushless motors with Encoders.

Click below for more information on the CAME-Single 3-Axis gimbal.

CAME-Single 3-Axis Gimbal

Vimeo user, Milton: Motion & Design, posted this video of his first test run right after opening his CAME-Single gimbal!

Click the picture below for more information on the CAME-Single gimbal.

CAME-Single 3-Axis Gimbal

 

Voyager Video, posted this quick test of the CAME-Mini 2 gimbal! It was shot with the Sony A7S and a Zeiss 24-70mm lens.

The new CAME-MINI 2 Gimbal is completely tool-less, which allows the operator to quickly change camera setups and re-balance the entire system for optimal performance. All of the wiring and electronics are enclosed into the frame offering a clean professional appearance and also protecting all the wiring.

CAME-Mini 2 3-Axis Gimbal

Click the picture below for more information on the CAME-Mini 2 Gimbal.

CAME-Mini 2 3-Axis Gimbal

 

3 Axis Gimbal Joystick
For camera systems such as the Panasonic GH4, Blackmagic Pocket Cinema Camera and Sony A7. A thumb controller joystick next to the right handle allows Pan and Tilt control.
Completely Enclosed Handles
All of the wiring and electronics are
completely enclosed into the frame.
Two side handles for hand-held use and a top handle for low-angle shots or for transporting.

FULL 3 AXIS STABILIZATION USING THE LATEST 32BIT CONTROLLERS WITH DUAL IMU SENSORS

YOU MIGHT BE INTERESTED IN THESE OTHER GIMBALS

CAME-Single
With Encoders
CAME-8000
Tool-less
CAME-7800
Tool-less
One of the first commercially available 3 Axis 32 bit Basecam controlled gimbals to offer motors with Encoders .... A handheld stabilizer designed for camera systems weighing up to 11 pounds, making it suitable for... Designed for camera systems such as Canon 5D3, Canon 5D2, Canon 7D, Panasonic GH4, and Sony A7...
read more read more read more

The CAME-7500 3-axis gimbal is designed to compensates for shakes, vibration or any unwanted jitter while shooting, allowing you to capture smoother shots that look like your camera is floating freely. The updated version of the CAME-7500, now includes new quick-release knobs that make it easier to adjust on the roll and yaw axis.

CAME-TV 7500 3-Axis Gimbal

Click the picture below for more information on the CAME-TV 7500 Gimbal.

CAME-TV 7500 3-Axis Gimbal

 

Mr.Cheesycam, uploaded this detailed video on how different profiles and settings can affect your CAME Mini 2 gimbal.

The video also has a nice split screen edit that clearly shows what he's doing in the program, so you can follow along with ease.

Screen Shot 2015-07-27 at 2.05.39 PM

Click the picture below for more information on the CAME Mini 2 gimbal.

CAME Mini 2 3-Axis Gimbal

3 Axis Gimbal Alexmos Board
For camera systems such as Canon 5D3, Canon 5D2, Canon 7D, Panasonic GH4, and Sony A7. 32-bit controller used for the construction of high quality 3-axis camera stabilizing systems.
Smooth Shots Handles
3 motors that stabilize along the pan, tilt, and roll axes. Two side handles for hand-held use and a top handle for low-angle shots or for transporting.

SUPPORTS LOADS UP TO 6.5 LBS AND INCLUDES
PRE-CALIBRATED 32-BIT ALEXMOS CONTROL BOARD

YOU MIGHT BE INTERESTED IN THESE OTHER GIMBALS

CAME-Single
With Encoders
CAME-8000
Tool-less
CAME-7800
Tool-less
One of the first commercially available 3 Axis 32 bit Basecam controlled gimbals to offer motors with Encoders .... A handheld stabilizer designed for camera systems weighing up to 11 pounds, making it suitable for... Designed for camera systems such as Canon 5D3, Canon 5D2, Canon 7D, Panasonic GH4, and Sony A7...
read more read more read more

Youtube user, SWAF Jarrad, posted some quick test footage from his CAME-Single 3-Axis gimbal. In the video, he does mention that he had some trouble in the beginning, but once he changed the lens on his camera, everything was a lot smoother. His setup in the video was a Panasonic GH-4 with a Panasonic 14-140mm lens. Check out his footage below!

Click the picture below for more information on the CAME-Single Gimbal.

CAME-TV Single 3-Axis Gimbal

Here's a quick test of the CAME-Single that AeroVideo shot with his Sony A7S camera plus a Sony 28-70mm lens.


The new CAME-SINGLE is one of the first commercially available 3-Axis 32-bit basecam controlled gimbals that offer brushless motors with Encoders.The design of the CAME-SINGLE allows the shooter to operate the gimbal with just one hand and has a 1/4-20 and 3/8 threaded mounting point located under the handle.

CAME-Single 3-axis gimbal

Click the picture below for more information on the CAME-Single

CAME-SINGLE 3-Axis Gimbal

Encoders Tool-less
This technology prevent motors from losing synchronization, skipping steps and more. 32-bit controller used for the construction of high quality 3-axis camera stabilizing systems.
Design Battery Life
The design of the CAME-SINGLE allows for one hand operation. Batteries can operate up 10 hours when fully charged.

ENCODERS ARE OFTEN USED IN ROBOTICS FOR HIGHLY ACCURATE MONITORING OF MOTOR POSITION

YOU MIGHT BE INTERESTED IN THESE OTHER GIMBALS

CAME-MINI 2
Tool-less
CAME-8000
Tool-less
CAME-7800
Tool-less
The new MINI2 is completely tool-less which allows the operator to change camera setups.... A handheld stabilizer designed for camera systems weighing up to 11 pounds, making it suitable for... Designed for camera systems such as Canon 5D3, Canon 5D2, Canon 7D, Panasonic GH4, and Sony A7...
read more read more read more

NextWaveDV, put together this quick video of them testing out the new CAME-Single 3-Axis Gimbal with a Sony A7s!

The CAME-Single is equipped with brushless motors that have encoders. The encoders prevent motors from losing synchronization, skipping steps, decreases power consumption, increases Torque, increases the precision of the stabilization and provides important information about frame and camera angles.

CAME-Single 3-Axis Gimbal

 

Click the picture below for more information on the CAME-Single 3-Axis Gimbal.

CAME-Single 3-Axis Gimbal

Max Snyder, uploaded this short video that shows test footage of him using the CAME-Mini 1 Gimbal for the first time! The wiring and electronics on the CAME-Mini 1 are completely enclosed into the frame, giving a clean professional appearance.

Click the picture below for more information on the CAME-Mini 3-Axis Gimbal.

CAME-TV Mini 3-Axis Gimbal