Owners of our CAME-Argo and Mini 3 might have noticed something different in each gimbal's battery configuration. We are now using a battery case that has 18650 LiPo batteries allowing you to remove them, charge them and immediately replace them with a backup set of fully charged 18650 LiPo batteries that you might have on standby. This allows you to keep cycling through numerous sets of batteries for an extended gimbal run time.
As with all LiPo batteries it is never good to over-discharge the battery. Over-discharge is when a battery cell voltage drops below the level of circuit protection limit. Once a LiPo battery is over-discharged, it is more than likely that it cannot be recharged and new one would have to be purchased.
We strongly recommend that when the gimbal is not in use or is in storage, to remove the 18650 LiPo batteries from the battery case. Failure to do so can result in over-discharge of the battery/batteries.
YouTube Reviewer MrCheesycam gives us a thorough breakdown of the updated battery packs in the video below:
Vimeo user, Gilles Havet uploaded this short video that follows some of the tennis players that were competing at the "International Women's Tournament" in Belgium. Some of the scenes in the video were shot with the CAME-7800 gimbal & CAME-Single! The cameras used were the Panasonic GH4 and Sony a6300.
The Single gimbal is designed to be operated with just one hand. The encoders on the CAME-Single: prevent the motors from losing sync/skipping steps, provides important information about the frame and also decreases the power consumption - increasing the battery life.
Although, the CAME-7800 gimbal is currently unavailable - we advise you to check out our new CAME-ARGO 3-axis gimbal. The CAME-ARGO features a 32 bit Alexmos Board and is completely tool-less, making balancing your camera setup easy and quick. The max payload that the ARGO can handle is about 6.6lbs , which is the same max payload as the 7800 gimbal.
Tom Antos, recently uploaded this detailed review on our CAME-ARGO Gimbal! Along with his overall impressions of the ARGO, he added some example footage he shot with the Canon 7D.
The CAME-ARGO features a 32-bit Alexmos Board and is completely tool-less for easy balancing. All of the motors are equipped with encoders, making the performance more smooth and accurate. The handle comes with a monitor mount and a wireless remote, which allows you to remotely control the gimbal and switch between modes. The entire top handle bar can be easily separated from the gimbal, allowing the ARGO to be mounted to other devices like a crane, slider or drone with the included adapter plate.
CREATIVE Team, recently uploaded their second test video on the CAME-TV ARGO gimbal! The video was shot with the Canon 5DmkIII with three different lenses; the Canon 24-105mm, 50mm and 18-200mm!
The CAME-ARGO features a 32 bit Alexmos Board and is completely tool-less, making balancing your camera setup easy and quick. All of the motors are equipped with encoders, which makes the ARGO's performance more smooth and accurate, along with increasing the lifespan of the battery.
Life2PRO - Travel Video, posted this stunning travel video of Siargao Island in the Philippines. He filmed it with the CAME-ARGO gimbal paired with the Sony A7s and the Zeiss 24-70mm lens!
The CAME-ARGO features a 32 bit Alexmos Board and is completely tool-less for easy balancing. All of the motors are equipped with encoders, making the gimbals performance more smooth and accurate. On the bottom of the ARGO there's a video transmitter along with a D-Tap out, which you can power an accessory like a wireless follow focus.
Youtube user, StabilizerNews uploaded this short film that follows a mountain biker as he goes for a ride through the woods. Except for the drone shots, the short was filmed mostly with the CAME-TV ARGO gimbal! He used the Canon 5DmkIII with two different lenses - the Canon 16-35mm & the Rokinon 35mm.
The CAME-ARGO features a 32 bit Alexmos Board and is completely tool-less. All of the motors are equipped with encoders, making the performance much more smooth and accurate while also increasing the lifespan of the battery. On the bottom of the ARGO's frame, there's a video transmitter along with a D-Tap out, which you can power an accessory like a wireless follow focus.
Youtube user, Scotty Ray uploaded this wonderfully shot backpacking video that documents his hike up to Clouds Rest in the famous Yosemite National Park. He filmed the video with the CAME-TV 7800 and Sony A7s. The two lenses he used was the Rokinon 14mm and the Zeiss 24-70mm.
The CAME-7800 3-Axis Camera Gimbal from CAME-TV is a handheld stabilizer designed for camera systems such as Canon 5Dmk3, Canon 5Dmk2, Canon 7D, Panasonic GH4, and Sony A7. It utilizes three motors that stabilize the camera along the pan, tilt, and roll axes. The CAME-7800 features a clean design that hides all of the wires. As with most sled-style stabilizers, your camera needs to be properly balanced in order to get the best performance out of the gimbal.
Although, the CAME-TV 7800 gimbal is currently sold out, we urge you to check out all our other gimbals like the CAME-TV ARGO, CAME-Single and CAME-Mini 3. Click the image below to see a list of all the gimbals we offer. Make sure to also sign up for our newsletter to receive updates and information on any new products we release.